Support | Dyson V10™ Animal Extra | Dyson Skip navigation
Thanks. We've saved your preferences.
You can update your contact preferences at any time in the Keep in touch section of Your Dyson. If you have a Your Dyson account, you can log in below to manage your contact options.

Please note:

Due to the upcoming bank holiday, there will be a delay in the delivery of orders placed after 4pm on the 15th of March. All orders will be shipped on the next working day.

Let's get your machine working.

Dyson V8 Animal Extra
Dyson V8 Animal Extra

Let's get your machine working.

Dyson V8 Animal Extra
Reference code:

How to charge the battery

The machine can be charged on the dock or by plugging the charger directly to the machine.

The light on the charger will show when the machine is being charged and will go out when charging is complete.

The battery should be fully charged after 5.5 hours.

Is there anything else we can help with?

Reference code:
Reference code:
Reference code:

Check the machine

The machine is designed to pulsate. This is an audible feature that indicates a problem, as well as preventing damage to the motor. This is usually caused by a restriction in airflow or a blockage within the machine.

Please select the appropriate option

Reference code:

The machine is designed to pulsate. This is an audible feature that indicates a restriction of airflow and prevents damage to the motor. This is usually caused by blockage within the machine or a clogged filter.

Check the Wand for blockages and remove as necessary.

                   
Reference code:

Check for blockages

With the accessory removed from the machine, check both ends for blockages and remove as necessary.

Refit the accessory back onto the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Reference code:

Press the red Bin release catch located to the rear of the clear bin.

Check the bin inlet

Check the bin inlet ensuring that it moves freely. Fluff or fibres jamming the hinge can cause the flap to close resulting in low suction and a pulsating noise.

                   

Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone.

Using the Combination tool, brush away any dust around the shroud of the cyclone.

Once cleared of any dust, press and hold the trigger for 10 seconds.

                   

Reassemble and test the machine.

Has this resolved the problem?

Reference code:

Remove the Wand

Remove the Cleaner head from the Wand, and remove the Wand from the machine.

Check both ends of the Wand for blockages and remove as necessary.

Refit the Cleaner head onto the Wand and connect the Wand back onto the machine.

Has this resolved the problem?

Reference code:

Wash the filters

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Reference code:

Washing the filters - step-by-step

To remove the pre-filter, lift it out of the top of the machine.

To unlock the post-filter, rotate it anti-clockwise until the two solid black dots line up.

With cold water only, run water over the outside of the filters until the water runs clear.

Turn the filter upside down and shake to remove any excess debris.

Squeeze and twist the pre-filter with both hands to make sure the excess water is removed, then tap and shake the post-filter to expel all debris.

Leave the filter to dry with the open end facing up for as long as possible.

Ensure the filter is completely touch dry prior to refitting.

WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.

To refit the filter, place the dry filter back into the top of the machine. Ensure it is fitted properly.

Rotate the post-filter clockwise until it locks in place and the solid black dot lines up with the empty circle.

Has this resolved the problem?

Reference code:

Clear the floor tool

On the side of the Direct drive cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

Check the brush bar drive cog and clear it from any hair or debris.

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Has this resolved the problem?

Reference code:

Clear the floor tool

On the side of the Cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

                   

Check the brush bar drive cog and clear it from any hair or debris.

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Has this resolved the problem?

Reference code:

Clear the floor tool

Under the Cleaner head by the Soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

                   

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Has this resolved the problem?

Reference code:

Open the bin

Pull the cyclone release catch upwards until the bin base opens.

                   

Remove the bin

Press the red catch underneath the bin once the bin base is open to release it from the machine.

Check the bin inlet

Check the bin inlet ensuring that it moves freely. Fluff or fibres jamming the hinge can cause the flap to close resulting in low suction and a pulsating noise.

Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone.

Using the Combination tool, brush away any dust around the shroud of the cyclone.

Once cleared of any dust, press and hold the trigger for 10 seconds.

                   

Has this resolved the problem?

Reference code:

Remove the filter

Pull the pre-filter out of the top of the cyclone and place the palm of your hand over the hole where the filter is usually positioned.

Press and hold the trigger for 10 seconds.

Does the noise still occur?

Reference code:

Our cordless vacuum filters are engineered to capture microscopic particles. Over time, these can build up in the filter and reduce performance. By washing the filter once a month you can help maintain suction power and prevent the machine from pulsating.

Wash the filter

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Reference code:

Washing the filters

To remove the pre-filter, lift it out of the top of the machine.

To unlock the post-filter, rotate it anti-clockwise until the two solid black dots line up.

With cold water only, run water over the outside of the filters until the water runs clear.

Turn the filter upside down and shake to remove any excess debris.

Squeeze and twist the pre-filter with both hands to make sure the excess water is removed, then tap and shake the post-filter to expel all debris.

Leave the filter to dry with the open end facing up for as long as possible.

Ensure the filter is completely touch dry prior to refitting.

WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.

To refit the filter, place the dry filter back into the top of the machine. Ensure it is fitted properly.

Rotate the post-filter clockwise until it locks in place and the solid black dot lines up with the empty circle.

Has this resolved the problem?

Reference code:

WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.

In most cases this would suggest that the filter is blocked

Please confirm the following steps to wash the filter below have been carried out and the machine has been retested.

Thoroughly wash the filter

Tap the cyclone against a hard surface.

See if there is any debris in the top of the filter.

Soak and massage the filter to dislodge any debris.

Run the filter under cold water.

Soak the filter again and confirm the water is clear.

Leave to dry for at least 24 hours.

Only place the filter in the machine when it’s completely dry.

Some variants may have a washable post-filter.

If it does, run the water into the open side of the post-filter, then tap and shake the filter to expel all debris.

Repeat the process until the water runs clear.

Has this resolved the problem?

Reference code:

Remove the post-filter

To unlock the post-filter, rotate it anti-clockwise until the two solid black dots line up.

Does the noise still occur?

Reference code:

Test the machine

Press and hold the trigger for 10 seconds.

Please ensure the cyclone is fitted correctly and the bin is closed. The machine may not power on if this has not been done.

Reference code:

Inspect the power cable

With the charger unplugged check the cable for any damage.

If no damage is found, plug the charger back in and in to the machine directly.

Wiggle the cable to see if you can get the machine to charge. If by moving the cable charges the machine, please select "Charger is faulty"

How to remove the charger from the dock

Remove the machine and its accessories from the dock and unplug the charger from the mains.

Using a screwdriver remove the two screws on the docking station.

With the dock removed, unfeed the cable through the channel on the back of the dock.

Try the machine in a different plug socket.

Charge the machine

Charge the machine without the dock for 3.5 hours.

Has this resolved the problem?

Reference code:

Charge the machine

Place the machine on charge.

Reference code:

Powerful mode
Up to 40 minutes

MAX mode
Up to 7 minutes

The overall run time can increase and decrease depending on the power mode and tool being used.

Has this resolved the problem?

Reference code:

Please select the appropriate option

Reference code:

Remove the tools

Remove all tools and accessories from the machine.

                   

Press and hold the trigger for 10 seconds.

Does the noise still occur?

Reference code:

Open the bin

Pull the cyclone release catch upwards until the bin base opens.

                   

Remove the bin

Press the red catch underneath the bin once the bin base is open to release it from the machine.

Check the bin inlet

Check the bin inlet ensuring that it moves freely. Fluff or fibres jamming the hinge can cause the flap to close resulting in low suction and a pulsating noise.

Press and hold the trigger for 10 seconds.

Does the noise still occur?

Reference code:

Clear the floor tool

On the side of the Direct drive cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head and connector pins (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

                   

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Has this resolved the problem?

Reference code:

Clear the floor tool

On the side of the Cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head and connector pins (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

                   

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Has this resolved the problem?

Reference code:

Clear the floor tool

Under the Cleaner head by the Soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head and connector pins (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

                   

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Has this resolved the problem?

Reference code:

Check the machine

To ensure the correct checks are carried out, we will need to determine if this is a pick up issue or if the machine is pulsating.

The machine is designed to pulsate. This is an audible feature that indicates a problem, as well as preventing damage to the motor. This is usually caused by a restriction in airflow or a blockage within the machine.

Please ensure the bin is empty before continuing with any checks.

Remove all tools and accessories from the machine e.g. Wand, Cleaner head, Crevice tool etc.

                   

Check both ends of the Wand for blockages and remove as necessary.

                   

Press and hold the trigger for 10 seconds.

                   

Does the issue occur without the tools?

Reference code:

Open the bin

Pull the cyclone release catch upwards until the bin base opens.

                   

Remove the bin

Press the red catch underneath the bin once the bin base is open to release it from the machine.

Check the bin inlet

Check the bin inlet ensuring that it moves freely. Fluff or fibres jamming the hinge can cause the flap to close resulting in low suction and a pulsating noise.

Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone.

Using the Combination tool, brush away any dust around the shroud of the cyclone.

Once cleared of any dust, press and hold the trigger for 10 seconds.

                   

Has this resolved the problem?

Reference code:

Check the floor tool

If the machine is not performing as well as it used to this is typically caused by a partial or full blockage within the openings of the machine.

Reference code:

Please select the appropriate option

Reference code:

Damp or musty smell

A damp or musty smell is caused when dust in the cyclone has come into contact with water.

It may not be a direct contact with water, for example when vacuuming pet hair that is slightly damp, this moisture will combine with the dust in the cyclone causing the smell.

Additionally the smell may occur if the filter goes back into the machine wet.

Only the filter can be washed, the bin can be cleaned with a damp cloth only, and both must be completely dry before being refitted to the machine.

Has any part of the machine been washed?

Reference code:

Were all the washed parts completely dry before the machine was used?

Reference code:

Under normal use, any unpleasant smell can only be caused by something the machine has picked up. Please select pick up issues to carry out checks.

If you are able to locate the smell to a part of the machine, replacing the part may help eliminate the smell. For this, please select Part broken.

Please select the appropriate option

Reference code:

Wash the filter

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Reference code:

Washing the filters

To remove the pre-filter, lift it out of the top of the machine.

                   

To unlock the post-filter, rotate it anti-clockwise until the two solid black dots line up.

                   

With cold water only, run water over the outside of the filters until the water runs clear.

                   

Turn the filter upside down and shake to remove any excess debris.

Squeeze and twist the pre-filter with both hands to make sure the excess water is removed, then tap and shake the post-filter to expel all debris.

                   

Leave the filter to dry with the open end facing up for as long as possible.

Ensure the filter is completely touch dry prior to refitting.

WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.

                   

To refit the filter, place the dry filter back into the top of the machine. Ensure it is fitted properly.

                   

Rotate the post-filter clockwise until it locks in place and the solid black dot lines up with the empty circle.

                   

Has this resolved the problem?

Reference code:

WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.

In most cases this would suggest that the filter is blocked

Please confirm the following steps to wash the filter below have been carried out and the machine has been retested.

Thoroughly wash the filter

Tap the cyclone against a hard surface.

See if there is any debris in the top of the filter.

Soak and massage the filter to dislodge any debris.

Run the filter under cold water.

Soak the filter again and confirm the water is clear.

Leave to dry for at least 24 hours.

Only place the filter in the machine when it’s completely dry.

Some variants may have a washable post-filter.

If it does, run the water into the open side of the post-filter, then tap and shake the filter to expel all debris.

Repeat the process until the water runs clear.

Has this resolved the problem?

Reference code:

Please check all floor tools

Please connect the floor tool directly on to the bin.

If the Brush bar on every tool spins when connected to the bin, please select the Wand is damaged.

Reference code:

Open the bin

Pull the cyclone release catch upwards until the bin base opens.

                   

Remove the bin

Press the red catch underneath the bin once the bin base is open to release it from the machine.

                   

Check the electrical contacts on the bin

Once the bin has been removed, clean the electrical contact from any dust.

The electrical contacts are located at the top of the bin where it connects to the Main body.

Has this resolved the problem?

Reference code:

Remove the bin

Pull the cyclone release catch upwards until the bin base opens.

                   

Press the red catch underneath the bin once the bin base is open to release it from the machine.

Clear any debris from behind the bin inlet flap.

Reassemble and test the machine.

Has this resolved the problem?

Reference code:

Please select the appropriate option

Reference code:

Remove the battery

There are 3 phillips screws that need to be removed, prior to removing the battery.

Remove the post-filter, then using a small phillips screwdriver unscrew the screw located on the rear of the Main body.

Place the Main body on its side on a flat surface, and locate the two screws near the battery.

Unscrew the screws and gently pull the battery away from the Main body.

Has this resolved the problem?

Reference code:

Remove the bin

Pull the cyclone release catch upwards until the bin base opens.

                   

Press the red catch underneath the bin once the bin base is open to release it from the machine.

Has this resolved the problem?

Reference code:

Check the Wand

Check the catch on the bin inlet for blockages or damage.

Make sure that it moves freely and springs back into position when pressed.

Check the end of the Wand for signs of damage.

                   

Has this resolved the problem?

Reference code:

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Reference code:

Installing the wall dock

Please note that wall fixings are not included with the dock.

Feed the charger cable through the rear of the dock, ensuring it is held via the retainer clip as shown in the image.

Clip the end of the charger cable in the small bracket located to the front of the dock until it clicks.

When securing the dock to the wall, ensure there is a distance of 1.2m/47¼” from the floor. This is to allow the machine to sit in the dock without touching the floor.

Is there anything else we can help with?

Reference code:

Getting started

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Is there anything else we can help you with?

Reference code:

Fully charge your machine prior to first use by plugging directly into the main body or by using the docking station.

A full charge from completely flat will take 5 hours. Three solid lights represent a high level of charge and will turn off once fully charged.

Attach the wand to the bin assembly, and attach the supplied main cleaner head (will vary depending on model).

When tackling stubborn or excessive dirt, 'Max mode' can be used.

To operate the max mode, locate the switch on the top of the appliance. Slide the switch to the Max mode position.

To switch off Max mode, slide the switch back to the Powerful suction mode position.

Any tools supplied with the machine can be fitted into the end of the wand.

Additionally, any tools supplied with the machine can also be fitted into the end of the bin assembly.

If your machine has a mini motorhead, it can provide the functionality of the main cleaner head but in hard to reach areas, such as your sofa.

Empty as soon as the dirt reaches the level of the MAX mark - do not overfill.

Pull the red lever upwards to release the cyclone. Continue until the bin base automatically open and releases the dirt.

Press the cyclone down fully. Close the bin base ensuring it clips shut.

Powerful mode
Up to 40 minutes

MAX mode
Up to 7 minutes

The overall run time can increase and decrease depending on the power mode and tool being used.

Is there anything else we can help you with?

Reference code:

Machine run time

The run time on Powerful suction mode is 25 minutes with the Motorised head, 30 minutes with the Mini motorised head, and 40 minutes with the combination tool and crevice tool.

                   

MAX mode - 7 minutes with all tools.

                   

Is there anything else we can help you with?

Reference code:

Assembling your Dyson machine

Attach the Wand to the machine via the bin inlet.

                   

Attach the floor tool to the end of the Wand until it clicks.

                   

Is there anything else we can help you with?

Reference code:

Finding the serial number

The serial number can be found underneath the machine on the battery.

                   

Is there anything else we can help you with?

Reference code:

Please open the PDF for the user guide.

Is there anything else we can help you with?

Reference code:

Empty the bin

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Is there anything else we can help you with?

Reference code:

Empty the bin

Empty as soon as the dirt reaches the level of the MAX mark - do not overfill. Ensure the machine is disconnected from the charger before emptying the clear bin. Be careful not to pull the 'ON' trigger.

                   

To release the dirt, hold the appliance by the handle, pull the red lever back and lift upwards.

                   

Continue until the bin base automatically opens and releases the dirt.

                   

Once the dirt is released, push the cyclone back down until it clicks.

                   

Close the bin base of the machine ensuring it clicks in to place.

To close, push the cyclone downwards until it is in the normal position and manually close the base of the bin. The base will click when it is securely in place.

                   

Is there anything else we can help you with?

Reference code:

Washing the filters

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Is there anything else we can help you with?

Reference code:

How to clean the bin and cyclone

Remove the clear bin by holding the machine by the handle and pulling the red lever back, and then lift upwards to release the cyclone.

                   

Press the red Bin release catch located to the rear of the clear bin.

                   

Remove the bin fully.

Clean the cyclone shroud with the brush on the combination tool to remove lint and dust.

Do not immerse the whole cyclone unit in water or pour water into the cyclones.

                   

Clean the cyclone shroud with the brush on the combination tool to remove lint and dust.

Do not immerse the whole cyclone unit in water or pour water into the cyclones.

                   

Ensure the bin is completely dry before replacing. To replace the bin, push it up and in to the Main body of the machine until it clicks in to place.

                   

Close the clear bin base so it clicks into place and is secure.

                   

Is there anything else we can help you with?

Reference code:

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Reference code:

Clear the floor tool - step by step

With the cleaner head removed from the machine, turn it over. On the underside of the cleaner head by the end of the soft roller, push the end cap up fully.

                   

Remove the brush bar from the Laser Slim Fluffy™ cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

                   

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

                   

Is there anything else we can help with?

Reference code:

Turn the cleaner head upside down so the underside of the cleaner head is facing you.

Push the end cap upwards until it opens and pull the brush bar out of the cleaner head.

                   

Remove the end cap from the brush bar. Do not wash the end cap.

                   

Hold the brush bar under running water and gently rub to remove any lint or dirt.

                   

Stand the brush bar upright as shown. Leave to dry completely for a minimum of 24 hours.

                   

Reattach the end cap to your brush bar.

                   

Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.

                   

Push the end cap until it clips securely back into the closed position.

                   

Is there anything else we can help with?

Reference code:

Clear the floor tool

On the side of the Cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

                   

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Is there anything else we can help you with?

Reference code:

Clean the floor tool

Undo one fastener to remove the Brush bar.

                   

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

                   

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

                   

Is there anything else we can help you with?

Learn more from your Dyson with the MyDysonᵀᴹ app

Download the MyDysonᵀᴹ app to register.

Enjoy quick access to personalised guides and 24/7 support.

We need a little more information to help us solve your issue.

Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

The Dyson guarantee

‘How to’ videos and tips

'How to ' videos and tips

To help you get the most from your machine. Quick and easy.
Exclusive owner benefits

Exclusive owner benefits

Priority access to previews of new Dyson technology, events and offers.
Expert advice. 7 days a week.

Expert advice. 7 days a week.

Freephone and live chat. The right advice for your machine, from real Dyson people.
Hassle-free repairs and replacement

Hassle-free repairs and replacement

Free replacement parts or repairs during your guarantee period. And if we can’t repair it, we’ll replace it.

Please get in touch.

Our experts are ready to help you.

Call us free on 01-475-7109

UK based helpline open
8:00am- 8:00pm Monday to Friday
8:00am- 6:00pm Saturday and Sunday