Let's get your machine working
V12 Detect Slim Absolute™Let's get your machine working
V12 Detect Slim Absolute™
-
-
Troubleshooting
-
The LCD screen
-
Battery alerts
-
Charging the battery
-
LEDs whilst charging
-
Issue resolved
-
No power
-
Issue not resolved, please speak to our Customer Support Team
-
Replacement part required
-
Replacement part required
-
No LEDs whilst charging
-
Inspect display
-
Replacement part required
-
Replacement part required
-
Blue flashing LEDs whilst charging
-
Blockage alert
-
Check for blockages
-
Select floor tool
-
Direct drive cleaner head
-
Check inlet
-
Clear the bin
-
Washing the filter - video
-
Washing the filter - step by step
-
Issue not resolved, please speak to our Customer Support Team
-
Hair screw tool pulsing
-
Laser Slim Fluffy™ cleaner head pulsing
-
Washing the brush bar
-
Fluffy Optic™ cleaner head pulsing
-
Washing the brush bar
-
Accessory blocked
-
Cutting out
-
Diagnostic screen
-
Issue resolved
-
Unable to exit manually
-
Filter attachment alert
-
Wash the filter - video
-
Washing the filter - step by step
-
Replacement part required
-
Filter wash alert
-
Particle count and graph
-
Understanding the particle count
-
Unusual noise
-
Grating or rattle
-
Check for blockages
-
Select floor tool
-
Direct drive cleaner head
-
Replacement part required
-
Fluffy Optic™ cleaner head
-
Replacement part required
-
Washing the brush bar
-
Hair screw tool
-
Replacement part required
-
Laser Slim Fluffy™ cleaner head
-
Replacement part required
-
Washing the brush bar
-
Replacement part required
-
Test the machine
-
Check the bin inlet
-
Replacement part required
-
High pitched whistle
-
Replacement part required
-
Pick up issues
-
Machine is not picking up well
-
Power or electrical issue
-
Cutting out
-
Run time
-
Run time inaccurate after removing from charge
-
Machine has no power
-
LED showing
-
No power
-
Replacement part required
-
No LED
-
Inspect display
-
Blue flashing LEDs whilst charging
-
Machine overheating
-
Performance checks
-
Check for blockages
-
The machine has power but no display
-
LED showing
-
Unusual smell
-
Damp or musty
-
Washing the filter - video
-
Damp or musty smell
-
Washing the filter - step by step
-
Damp or musty smell
-
Damp or musty smell still present
-
Replacement part required
-
Issue not resolved, please speak to our Customer Support Team
-
Visible issue
-
Dark spots
-
Laser or light not working
-
Laser not working
-
Laser not working
-
Replacement part required
-
Check the inlet
-
Test another tool
-
Replacement part required
-
Issue not resolved, speak to our Customer Support Team
-
Light not working
-
Check the inlet
-
Test another tool
-
Replacement part required
-
The brush bar is not spinning on the floor tool
-
Direct drive cleaner head
-
Replacement part required
-
Hair screw tool
-
Replacement part required
-
Laser Slim Fluffy™ cleaner head
-
Fluffy Optic™ cleaner head
-
Washing the brush bar
-
Replacement part required
-
Replacement part required
-
Replacement part required
-
Filter blocking frequently
-
Emptying the bin - video
-
Emptying the bin - step by step
-
The reactive suction power isn't working
-
Issue not resolved, please speak to our Customer Support Team
-
Clean the bin
-
Popular queries
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
The Dyson guarantee
'How to ' videos and tips
To help you get the most from your machine. Quick and easy.
Exclusive owner benefits
Priority access to previews of new Dyson technology, events and offers.
Expert advice. 7 days a week.
Freephone and live chat. The right advice for your machine, from real Dyson people.
Hassle-free repairs and replacement
Free replacement parts or repairs during your guarantee period. And if we can’t repair it, we’ll replace it.
We need a little more information to help us solve your issue.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
You might need a replacement part.
It looks like the Main body and Cyclone is not working. You can solve this by ordering a new one below.
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
€88.00
You might need a replacement part.
It looks like the Main body and Cyclone is not working. You can solve this by ordering a new one below.
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
€88.00
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
The Dyson guarantee
'How to ' videos and tips
To help you get the most from your machine. Quick and easy.
Exclusive owner benefits
Priority access to previews of new Dyson technology, events and offers.
Expert advice. 7 days a week.
Freephone and live chat. The right advice for your machine, from real Dyson people.
Hassle-free repairs and replacement
Free replacement parts or repairs during your guarantee period. And if we can’t repair it, we’ll replace it.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
You might need a replacement part.
It looks like the Hair Screw Tool is not working. You can solve this by ordering a new one below.
Hair Screw Tool
Part no. 972213-02
Anti-tangle conical brush bar picks up long hair and pet hair. Fast.
€50.82
Hair Screw Tool
Part no. 972213-02
Anti-tangle conical brush bar picks up long hair and pet hair. Fast.
€50.82
€50.82
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
You might need a replacement part.
It looks like the Bin is not working. You can solve this by ordering a new one below.
Bin
Part no. 965272-01
Replacement bin for your Dyson vacuum cleaner.
€24.50
Bin
Part no. 965272-01
Replacement bin for your Dyson vacuum cleaner.
€24.50
€24.50
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
The Dyson guarantee
'How to ' videos and tips
To help you get the most from your machine. Quick and easy.
Exclusive owner benefits
Priority access to previews of new Dyson technology, events and offers.
Expert advice. 7 days a week.
Freephone and live chat. The right advice for your machine, from real Dyson people.
Hassle-free repairs and replacement
Free replacement parts or repairs during your guarantee period. And if we can’t repair it, we’ll replace it.
You might need a replacement part.
It looks like the Main body and Cyclone is not working. You can solve this by ordering a new one below.
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
€88.00
We need a little more information to help us solve your issue.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
You might need a replacement part.
It looks like the Main body and Cyclone is not working. You can solve this by ordering a new one below.
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
€88.00
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
We need a little more information to help us solve your issue.
But our Customer Support Team will be able to solve your problem.
Please contact our customer service team on 01-475-7109, or directly on Live Chat through our Digital Assistant by clicking the purple icon at the bottom of the page. You can start a conversation with an Expert by clicking the agent icon at the bottom left of the chat window.
You might need a replacement part.
It looks like the Main body and Cyclone is not working. You can solve this by ordering a new one below.
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
€88.00
You might need a replacement part.
It looks like the Wand is not working. You can solve this by ordering a new one below.
Wand
Part no. 971518-12
Replacement wand for your Dyson vacuum cleaner.
€42.00
Wand
Part no. 971518-12
Replacement wand for your Dyson vacuum cleaner.
€42.00
You might need a replacement part.
It looks like the Main body and Cyclone is not working. You can solve this by ordering a new one below.
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
Main body and Cyclone
Part no. 971640-02
Replacement Main body & Cyclone for your Dyson vacuum cleaner.
€88.00
€88.00
Unless prompted to do so, do not press the power button when checking any part of the machine. Operating the machine while it is partially dismantled could result in personal injury.
Please select the appropriate option
Alerts
The screen will alert you when your machine needs your attention.
The alert will flash for approximately 5 seconds, proceeded by a playable graphic. Follow the instructions on screen to maintain performance.
Please select the appropriate option
Low battery
Fully charge the machine.
The machine can be charged by either attaching the battery to the machine or by charging the battery separately.
Please select the next step
Please ensure the battery is charged to 100% after every use.
Charge the machine
Connect to the charger either directly or in the docking station.
The blue LEDs on each side of the battery should light up.
Which lights are showing?
The blue LEDs – one on each side of the battery – will flash on and off during charging.
When the battery is charged, both LEDs will light for 5 seconds, then go out.
The screen will also show the battery charge level at 100%.
The machine can take up to 4 hours to fully charge.
Press the ON/OFF button
Remove the charger from the machine and press the ON/OFF button.
The LED lights should be on constantly when in use.
If the LED lights blink on/off for approximately 10 seconds when the power button is pressed, please select 'LED lights blinking'.
Do the blue LED lights appear on either side of the battery?
Dock charging
If the machine is being charged through the docking station, please disconnect the charger and connect it directly into the machine.
Please check household electrics or use an alternative plug socket.
Remove the charger
Press the power button and run the machine for 10 seconds.
The blue LEDs – one on each side of the battery – will flash on and off during charging.
When the battery is charged, both LEDs will light for 5 seconds, then go out.
The screen will also show the battery charge level at 100%.
The machine can take up to 4 hours to fully charge.
Automatic cut out
Large items may block the machine or tools. If any part becomes blocked or the filter needs washing, the machine may automatically cut out.
Motor is pulsating
This will happen after the motor pulses a number of times (i.e. switches on and off in quick succession) and the blockage indicator will light. Leave to cool down before looking for blockages.
Be careful not to press the 'ON/OFF' button while looking for blockages. Operating the machine while it is partially dismantled could result in personal injury.
Remove the tools
Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.
Turn on and test the machine.
Turn the machine off.
Check for blockages
Check both ends of the wand for blockages and remove as necessary.
Reattach the cleaner head, tool or accessory to the wand. Reattach the wand to the machine. Please ensure that the red dot on the cleaner head and wand are aligned.
Turn on and test the machine.
Which floor tool are you using?
Clear the floor tool
On the side of the cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the brush bar from the Direct drive cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.
The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.
Check the bin inlet
Check the inlet at the front of the machine for any blockages and remove as necessary.
Check the shroud opening
Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.
Check the opening on the cyclone shroud for any blockages. Remove as necessary.
Close the clear bin by pushing the bin base upwards until it clicks into place.
Turn on and test the machine.
Remove the bin
Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.
Press the red button located on the bin runner to release the bin and slide the bin off the runner.
Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone. Using the combination tool, clean the shroud to remove any debris around the cyclone.
Check the cyclone for blockages and remove as necessary.
To refit the clear bin
Insert the spine into the bin runner.
Close the clear bin by pushing the bin base upwards until it clicks into place.
Attach the wand and cleaner head and test the machine.
Please follow the steps in the video.
Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"
Has this resolved the problem?
Removing the filter
Remove the filter by turning it anticlockwise. Gently pull it away from the machine.
Gently tap the filter unit to remove any excess dust and debris before washing it.
Wash the filter in warm running tap water.
WARNING: Please do not use detergent, do not wash in a dishwasher or washing machine.
Wash the pleated paper element of the filter unit first; hold the filter unit under warm running tap water with the foam element downwards and run warm water over the pleated paper. Continue washing until the water runs clear.
Wash the foam element of the filter unit next; hold the filter unit under warm running water tap with the foam element downwards so that dirty water does not contaminate the pleated paper element. Run warm water over the inside and outside of the foam element and squeeze the foam gently to expel the dirt. Continue washing until the water runs clear.
Wash the outside of the filter unit. Then fill the unit with warm water, place your hands over the open ends and shake gently. Repeat washing the elements and outside of the filter unit until the water runs clear.
Gently shake the filter unit to remove any excess water and leave to drain with the foam element end facing up.
Drying
Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.
Refit
Insert the filter back into the machine. Turn the filter clockwise until it clicks into place.
The filter may need to be washed more frequently if you are vacuuming a lot of fine dust, or if the machine is predominantly being used in Boost mode.
Your Hair screw tool doesn't have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions.
Remove the cover and brush bar
Remove the Hair screw tool from the machine.
Push the base plate open. Press the red lever down to release the cleaner head cover.
Pull the cleaner head cover off the main body of the tool.
Look for obstructions
Pull your brush bar firmly to remove it from the main body.
Check and remove any obstructions from all three parts of your Hair screw tool.
Your Hair screw tool isn't washable. Wipe over with a damp lint-free cloth.
Don't put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Re-assemble Hair screw tool
Put your brush bar back into position and press firmly until it clicks back into position.
Check the red locking lever is in the unlocked position. Align the cleaner head cover with the guide of the main body. Push it down until it clicks into position.
Push the red locking lever up until it clicks into position and push the base plate back into place.
Remove any debris from the brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Has this resolved the problem?
Turn the cleaner head upside down so the underside of the cleaner head is facing you.
Push the end cap upwards until it opens and pull the brush bar out of the cleaner head.
Remove the end cap from the brush bar. Do not wash the end cap.
Hold the brush bar under running water and gently rub to remove any lint or dirt.
Stand the brush bar upright as shown. Leave to dry completely for a minimum of 24 hours.
Reattach the end cap to your brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Remove any debris from the brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Has this resolved the problem?
Turn the cleaner head upside down so the underside of the cleaner head is facing you.
Push the end cap upwards until it opens and pull the brush bar out of the cleaner head.
Remove the end cap from the brush bar. Do not wash the end cap.
Hold the brush bar under running water and gently rub to remove any lint or dirt.
Stand the brush bar upright as shown. Leave to dry completely for a minimum of 24 hours.
Reattach the end cap to your brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Check for blockages
With the accessory removed from the machine, check both ends for blockages and remove as necessary.
Refit the accessory back onto the machine.
Press the power button and run the machine for 10 seconds.
Turn the machine off.
Push the red release button, taking care not to press the power button. The bottom of the bin will open and the shroud will slide down inside the bin, wiping away any dirt.
Push the red bin release lever on the bin runner and slide the bin off the runner.
Check the opening of the shroud for any blockages. Remove as necessary.
Check the shroud inlet
Check the shroud inlet at the front of the machine for any blockages and remove as necessary.
Close the clear bin by pushing the bin base upwards until it clicks into place.
Turn on and test the machine.
Diagnostic screen
The menu is accessed by pressing the selector button with the filter removed. Three options are displayed when accessing this menu screen.
Versions, displays the software versions of the machine.
Diagnostic, displays a series of numbers, letters and percentages.
Exit, you can exit the menu by selecting this option.
Check the filter
Before exiting the menu, please ensure the filter is fitted correctly.
The filter unit should be securely fitted onto the main body and turned clockwise until it clicks into place.
Exiting the menu
Once the filter is securely in place, press and hold the selector button for approximately 10 seconds or until the screen reverts back to the main display screen.
If you are unable to revert back to the main display screen manually, it can be achieved by leaving the machine to go inactive (around 15 minutes of no interaction).
If the filter isn't correctly fitted, the machine will not turn on when pressing the 'ON/OFF' button.
Removing the filter
Remove the filter by turning it anticlockwise. Gently pull it away from the machine.
Refit
Insert the filter back into the machine. Turn the filter clockwise until it clicks into place.
Turn on and test the machine.
This alert will continue until maintenance has been carried out.
Please follow the steps in the video.
Find the text version of the step-by-step guide instead, under "Has washing the filter resolved the problem?"
Has washing the filter resolved the problem?
The filter may need to be washed more frequently if you are vacuuming a lot of fine dust, or if the machine is predominantly being used in Boost mode.
Removing the filter
Remove the filter by turning it anticlockwise. Gently pull it away from the machine.
Gently tap the filter unit to remove any excess dust and debris before washing it.
Wash the filter in warm running tap water.
WARNING: Please do not use detergent, do not wash in a dishwasher or washing machine.
Wash the pleated paper element of the filter unit first; hold the filter unit under warm running tap water with the foam element downwards and run warm water over the pleated paper. Continue washing until the water runs clear.
Wash the foam element of the filter unit next; hold the filter unit under warm running water tap with the foam element downwards so that dirty water does not contaminate the pleated paper element. Run warm water over the inside and outside of the foam element and squeeze the foam gently to expel the dirt. Continue washing until the water runs clear.
Wash the outside of the filter unit. Then fill the unit with warm water, place your hands over the open ends and shake gently. Repeat washing the elements and outside of the filter unit until the water runs clear.
Gently shake the filter unit to remove any excess water and leave to drain with the foam element end facing up.
Drying
Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.
Refit
Insert the filter back into the machine. Turn the filter clockwise until it clicks into place.
This alert will continue until maintenance has been carried out.
Please follow the steps in the video.
Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"
Has this resolved the problem?
Your vacuum counts and measures the size of dust particles as you clean.¹ The LCD screen shows what’s been sucked up, displaying real-time scientific proof of a deep clean.²
The particle count is available in all power modes and with all attachments. Like our clear bin filling with dust, you can see debris increase on-screen as you clean.
Settings menu
Control the settings on your machine using the selection button. To enter the settings menu, press and hold the button until the menu screen appears. Tap to scroll through the options available.
Particle count and graph
You can turn the measuring and counting of particles on and off. Turning off the particle count and graph will stop your machine automatically adjusting suction power.
Adjust reactive suction power sensitivity
Use the selection button to change how sensitive the particle count is. This will change how your machine automatically reacts to dust particles.
Exit settings menu
Tap to scroll through the selection menu. Select 'Exit menu'.
¹Tested to EN 60312-1:2017 CL5.1, CL5.2 and CL5.3 for hard floors, crevices and carpets in Boost mode.
²Quantity of dust displayed on-screen varies depending on usage.
Please select the next step
As dust enters your vacuum, the particles are continuously counted and categorise in size from 10-500 microns (µm) and above. Real-time results are displayed in the particle count.
Yellow bar
10µm – particles as small as allergens and pollen
Orange bar
60µm – particles as small as microscopic dust and skin flakes
Pink bar
180µm – particles as small as dust mites and fine sand
Purple bar
500µm – particles as small as sugar and fleas¹
¹Particle sizes and densities vary. Examples shown may occur within one or more displayed size range. Some particles have a range including sizes smaller than 10µm, which may not be detected.
Please select the appropriate option
Test the machine
Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.
Put the machine in Boost mode.
Turn on and test the machine.
Turn the machine off.
Check for blockages
Check both ends of the wand for blockages and remove as necessary.
Reattach the cleaner head, tool or accessory to the wand. Reattach the wand to the machine. Please ensure that the red dot on the cleaner head and wand are aligned.
Turn on and test the machine.
Which floor tool are you using?
Turn the cleaner head upside down so the underside of the cleaner head is facing you.
Push the end cap upwards until it opens and pull the brush bar out of the cleaner head.
Remove any debris from the brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Has this resolved the problem?
Turn the cleaner head upside down so the underside of the cleaner head is facing you.
Push the end cap upwards until it opens and pull the brush bar out of the cleaner head.
Remove any debris from the brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Has this resolved the problem?
Remove the bin
Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.
Press the red button located on the bin runner to release the bin and slide the bin off the runner.
Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone. Using the combination tool, clean the shroud to remove any debris around the cyclone.
Turn on and test the machine.
Check the bin inlet
Check the opening on the cyclone shroud for any blockages. Remove as necessary.
To refit the clear bin
Insert the spine into the bin runner.
Close the clear bin by pushing the bin base upwards until it clicks into place.
Turn on and test the machine.
Check the machine
Please ensure the bin is empty before continuing with any checks.
Remove all tools and accessories from the machine e.g. Wand, Cleaner head, Crevice tool etc.
Check both ends of the Wand for blockages and remove as necessary.
Press and hold the trigger for 10 seconds.
Please select the appropriate option
Before testing the machine please ensure that any hair or loose clothing is clear of the machine.
The suction power of the machine varies depending which power mode you have selected. Boost mode being the most powerful.
Pick up issues are typically caused by a blockage.
Turn the machine off.
Remove the tools
Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.
Turn on and test the machine.
Please note: we've removed the trigger, so you can swap hands easily while cleaning around obstacles.
Please select the appropriate option
Automatic cut out
This machine is fitted with an automatic cut out. If any part becomes blocked, the machine may automatically cut out.
The display of your machine will alert you when simple maintenance steps are needed.
Which alert is showing?
Please ensure the battery is charged to 100% after every use.
Power modes
The machine has three power modes for different tasks. The overall run time is displayed on the digital display screen in minutes and seconds and will vary between each of the three power modes.
Run time
The overall run time can increase and decrease depending on the power mode, floor type and tool being used. Any change to the run time can take up to 30 seconds to appear on the digital display.
Eco mode
Maximum run time for longer cleans all around your home.
Auto/Med mode
The optimum balance of power and run time.
Attach your cleaner head or Hair screw tool to activate Auto mode. Suction power automatically adapts to dust levels.
Boost mode
Designed for intensive spot cleaning of ground-in dirt.
Run time information
Motorhead Fluffy™ (Carpet) - Eco mode (30 mins) Auto/Med mode (20 mins) Boost mode (5 mins)
Motorhead Fluffy™ (Hard floors) - Eco mode (50 mins) Auto/Med mode (30 mins) Boost mode (5 mins)
Motorhead Direct Drive cleaner head (Carpet) - Eco mode (30 mins) Auto/Med mode (20 mins) Boost mode (5 mins)
Motorhead Direct Drive cleaner head (Hard floors) - Eco mode (40 mins) Auto/Med mode (20 mins) Boost mode (5 mins)
Handheld ONLY - Eco mode (60 mins) Auto/Med mode (30 mins) Boost mode (5 mins)
Is the machine working as expected?
Please ensure the battery is charged to 100% after every use.
When the machine is placed on charge it enters an idle state, this reduces all power consumption ready for the next use. Due to this reduction in the power, when the machine is removed from charge and powered on for the first time it can display an incorrect run time. This is nothing to be concerned about. The machine will assess the charge capacity and current usage within 30 seconds, displaying the correct time on the digital display.
To achieve the maximum run time, the machine must first be calibrated. The machine should be fully charged approximately five times. Between charges, use the machine until it has no battery remaining.
Where you have additional click-in batteries, we recommend alternating and charging all click-in batteries regularly to prolong battery health.
Charge the machine
Connect to the charger either directly or in the docking station.
Charge the machine
When the battery is charged, both LEDs will light for 5 seconds, then go out.
Remove the charger
Turn on and test the machine.
Test the machine
Turn on and test the machine.
The LED lights should be on constantly when in use.
If the LED lights blink on/off for approximately 10 seconds when the 'ON/OFF' button is pressed, please select 'LED lights blinking'.
Do the blue LED lights appear on either side of the battery?
Charging
If the machine is being charged through the docking station, please disconnect the charger and connect it directly into the machine.
Please check household electrics or use an alternative plug socket.
Remove the charger
Turn on and test the machine.
The blue LEDs – one on each side of the battery – will flash on and off during charging.
When the battery is charged, both LEDs will light for 5 seconds, then go out.
The machine can take up to 4 hours to fully charge.
Remove the charger
Turn on and test the machine.
Most Dyson vacuums have a built in safety mechanism that will turn off the machine if it begins to overheat. This typically happens when the machine is blocked, or if the filter needs washing.
If your machine continues to overheat, please allow it to cool before carrying out the performance checks.
Please select the next step
Before testing the machine please ensure that any hair or loose clothing is clear of the machine.
Automatic cut out
This machine is fitted with an automatic cut out. If any part becomes blocked, the machine may automatically cut out.
Motor is pulsating
This will happen after the motor pulses a number of times (i.e. switches on and off in quick succession) and the blockage indicator will light. Leave to cool down before looking for blockages.
Be careful not to press the 'ON/OFF' button while looking for blockages. Operating the machine while it is partially dismantled could result in personal injury.
Remove the tools
Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.
Turn on and test the machine.
Check for blockages
Check both ends of the wand for blockages and remove as necessary.
Reattach the cleaner head, tool or accessory to the wand. Reattach the wand to the machine.
Turn on and test the machine.
Charge the machine
Connect to the charger either directly or in the docking station.
The blue LEDs – one on each side of the battery – will flash on and off during charging.
Charge the machine
When the battery is charged, both LEDs will light for 5 seconds, then go out.
Remove the charger
Turn on and test the machine.
Please select the appropriate option
Damp or musty
A damp or musty smell is caused when dust in the cyclone has come into contact with water.
It may not be a direct contact with water, for example when vacuuming pet hair that is slightly damp, this moisture will combine with the dust in the cyclone causing the smell.
Additionally the smell may occur if the filter goes back into the machine wet.
Wipe with a damp, lint-free cloth, without touching the connector end.
Make sure your tools are completely dry before using.
Combination tool
Mattress tool
Stubborn dirt brush
Crevice tool
Light crevice tool
Flexi crevice tool
Low-reach adaptor
Soft dusting brush
Up-top tool
Extension hose
Don’t put any part of your machine in a dishwasher or use detergent, polishes or air fresheners.
Remove the bin
Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.
Press the red button located on the bin runner to release the bin and slide the bin off the runner.
Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone. Using the combination tool, clean the shroud to remove any debris around the cyclone.
Check the opening on the cyclone shroud for any blockages. Remove as necessary.
The clear bin is not dishwasher safe and the use of detergents, polishes or air fresheners to clean the clear bin is not recommended as this may damage your machine. Clean the clear bin with a damp cloth only.
To refit the clear bin
Insert the spine into the bin runner.
Close the clear bin by pushing the bin base upwards until it clicks into place.
Please follow the steps in the video.
Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"
Has this resolved the problem?
Damp or musty smell still present
Under normal use, any unpleasant smell can only be caused by something the machine has picked up. Please select pick up issues to carry out checks.
Please select the next step
Removing the filter
Remove the filter by turning it anticlockwise. Gently pull it away from the machine.
Gently tap the filter unit to remove any excess dust and debris before washing it.
Wash the filter in warm running tap water.
WARNING: Please do not use detergent, do not wash in a dishwasher or washing machine.
Wash the pleated paper element of the filter unit first; hold the filter unit under warm running tap water with the foam element downwards and run warm water over the pleated paper. Continue washing until the water runs clear.
Wash the foam element of the filter unit next; hold the filter unit under warm running water tap with the foam element downwards so that dirty water does not contaminate the pleated paper element. Run warm water over the inside and outside of the foam element and squeeze the foam gently to expel the dirt. Continue washing until the water runs clear.
Wash the outside of the filter unit. Then fill the unit with warm water, place your hands over the open ends and shake gently. Repeat washing the elements and outside of the filter unit until the water runs clear.
Gently shake the filter unit to remove any excess water and leave to drain with the foam element end facing up.
Drying
Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.
Refit
Insert the filter back into the machine. Turn the filter clockwise until it clicks into place.
The filter may need to be washed more frequently if you are vacuuming a lot of fine dust, or if the machine is predominantly being used in Boost mode.
Damp or musty smell still present
Under normal use, any unpleasant smell can only be caused by something the machine has picked up. Please select pick up issues to carry out checks.
If you are able to identify which part of the machine the smell is coming from, replacing this part may resolve the issue.
Please select the appropriate option
If dark spots are observed on the floor when using the Laser Slim Fluffy™ cleaner head, this could be caused by a dirty lens. Please follow the steps below.
Switch the laser off.
Use a soft, dry, lint-free cloth to wipe the lens.
Please do not use a wet cloth to clean the lens as this may cause smearing and smudging. We would also advise not to use cleaning agents when cleaning the lens.
Confirm cleaner head
Your machine could have either the Laser Slim Fluffy™ cleaner head or the Fluffy Optic™ cleaner head. If you’re unsure on which one you have, you can check the wording on the top of the cleaner head. The Laser Slim Fluffy™ will also have a ON/OFF switch for the laser, whereas the Fluffy Optic™ cleaner head does not.
Please select the appropriate option
Turn the Laser ON/OFF
Try turning the Laser ON/OFF using the switch on the cleaner head.
Turn on and test the machine.
Class 1 Laser product - Safe for pets and humans. Avoid looking directly into the beam.
Test the Wand
Remove the Laser Slim Fluffy™ cleaner head from the Wand.
Remove the Wand from the machine.
Put the Laser Slim Fluffy™ cleaner head directly onto the machine and test.
Check the front inlet
Check the bin inlet connections to ensure that they are not bent or damaged.
Test with another tool
Put another motorised tool directly onto the machine and test.
Test the Wand
Remove the Fluffy Optic™ cleaner head from the Wand.
Remove the Wand from the machine.
Put the Fluffy Optic™ cleaner head directly onto the machine and test.
Check the front inlet
Check the bin inlet connections to ensure that they are not bent or damaged.
Test with another tool
Put another motorised tool directly onto the machine and test.
Please check all floor tools
Please connect the floor tool directly on to the bin.
If the brush bar on every tool spins when connected to the bin, please select "The wand is damaged".
If the brush bar isn't spinning on any tool, please select "The brush bar does not spin on any cleaner head".
Clear the floor tool
With the Direct drive cleaner head removed from the machine, turn it over and undo the fastener.
Locate the end cap and using a coin, turn it anticlockwise a quarter of the way. This will allow you to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the brush bar from the Direct drive cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.
The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.
Your Hair screw tool doesn't have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions.
Remove the cover and brush bar
Remove the Hair screw tool from the wand or machine.
Push the base plate open. Press the red lever down to release the cleaner head cover.
Pull the cleaner head cover off the main body of the tool.
Look for obstructions
Pull your brush bar firmly to remove it from the main body.
Check and remove any obstructions from all three parts of your Hair screw tool.
Your Hair screw tool isn't washable. Wipe over with a damp lint-free cloth.
Don't put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Re-assemble Hair screw tool
Put your brush bar back into position and press firmly until it clicks back into position.
Check the red locking lever is in the unlocked position. Align the cleaner head cover with the guide of the main body. Push it down until it clicks into position.
Push the red locking lever up until it clicks into position and push the base plate back into place.
Turn the cleaner head upside down so the underside of the cleaner head is facing you.
Push the end cap upwards until it opens and pull the brush bar out of the cleaner head.
Remove any debris from the brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Has this resolved the problem?
Confirm cleaner head
Your machine could have either the Laser Slim Fluffy™ cleaner head or the Fluffy Optic™ cleaner head. If you’re unsure on which one you have, you can check the wording on the top of the cleaner head. The Laser Slim Fluffy™ will also have a ON/OFF switch for the laser, whereas the Fluffy Optic™ cleaner head does not.
Remove any debris from the brush bar.
Slide the brush bar back onto the cleaner head, around the motor. The end cap should be in the open position as shown.
Push the end cap until it clips securely back into the closed position.
Has this resolved the problem?
Please ensure that you are emptying the bin as soon as the dirt reaches the level of the MAX mark.
Should the dirt in the bin exceed the MAX mark, the excess dirt can be pulled directly into the filter causing a blockage.
Has this resolved the problem?
Please follow the steps in the video.
Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"
Has this resolved the problem?
Empty as soon as the dirt reaches the level of the MAX mark - do not overfill. Ensure the machine is disconnected from the charger before emptying the clear bin.
Remove the wand by pressing the red wand release button and pulling away from the bin.
Emptying the bin
Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.
Closing the bin
Close the clear bin by pushing the bin base upwards until it clicks into place.
Attach your cleaner head or Hair screw tool to activate Auto mode. Suction power automatically adapts to dust levels.
Test the reactive suction power by placing a small pile of debris on the floor such as rice, sugar or cereal. You should notice a change in power during pick-up.
Settings menu
Control the settings on your machine using the selection button. To enter the settings menu, press and hold the button until the menu screen appears. Tap to scroll through the options available.
Adjust reactive suction power sensitivity
Use the selection button to change how sensitive the particle count is. This will change how your machine automatically reacts to dust particles.
Exit settings menu
Tap to scroll through the selection menu. Select 'Exit menu'.